霧化噴嘴|上海斐卓Feizhuo|內混式空氣霧化噴嘴

小流量空氣霧化噴嘴BIM系列：

產生平均粒徑100micron以下之“微霧”的二流體扇形噴嘴；

對噴霧液體加0.1-0.3MAa程度之壓力的液體加壓式，有很廣的流量調整范圍；

噴霧角度60°。

產生平均粒徑30micron以下之微霧的二流體扇形噴嘴，不需要供給液體加壓裝置之虹吸式。

一般應用：

散步：脫模機、除臭劑、油、表面處理劑、防銹劑、潤滑劑、蜂蜜、防蟲劑、尿素水、其他；

冷卻：模具、氣體、鋼板、鋼片、鑄物、車體、涂裝物、玻璃板、塑膠、其他。

調濕：紙、廢氣、陶瓷、混凝土、其他

洗凈：精密基板、玻璃管、其他

Small flow air atomizing nozzle BIM series:

Below the erage particle size of 100 micron 'micro fog' two fluid fan nozzle;

To spray liquid pressure of 0.1 to 0.3 degree of MAa liquid pressure type， there is a wide range of flow adjusting range;

The spray Angle 60 °.

have an erage particle size of micro fog two fluid under 30 micron fan nozzle， do not need to supply the siphon type of liquid pressure device.

General application:

Walking: stripper， deodorant， oil， surface treatment agent，霧化噴嘴， anti-rust agent， lubricant， honey， pest cool， urea and other water;

Cooling: mold，二流體霧化噴嘴噴頭， gas， steel plates， steel sheets， ting material， car body， coating material， glass， plastic and other.

Humidity: paper， waste gas， ceramic， concrete， other

Wash: precision base board， glass tube， the other

空氣霧化噴嘴壓力輸送噴霧裝置（內混式）

噴霧噴嘴的優點和特性：

對于扇形噴霧，內混式空氣霧化噴嘴，尺寸A、B、和C是距離噴嘴相應距離處的噴霧寬度。

從噴嘴到很大彌散點的噴霧投射總距離為D.

當使用壓力輸送液體系統時，液體通過壓力被送往噴嘴。液體和壓縮空氣或者其他氣體在內部被混合，以產生完全霧化的噴霧。

Air atomizing nozzle pressure spray device (mixed type)

The advantages of spray nozzle and features:

For the fan-shaped spray， size A， B，不銹鋼 霧化噴嘴， and C corresponding distance is the distance the nozzle spray width.

The spray from the nozzle to the maximum dispersion point projected a total distance of D.

When using pressure conveying liquid system， through the pressure to the nozzle.Liquid and compressed air or other gas was mixed in internal， to produce a fully atomized spray.