顎式破碎機,顎式破石機,鄂式碎石機,顎破,鄂破機-顎式破碎機,顎式顎式破碎機PE600x900

顎式破碎機,顎式破石機,鄂式碎石機,顎破,鄂破機-顎式破碎機,顎式 常見故障 故障介紹 顎式破碎機在運行過程中承受力矩或振動較大，常會造成傳動系統故障，常見的有：皮帶輪與軸頭部位產生間隙造成的軸頭與輪轂?zāi)p，偏心軸受力造成的軸承位磨損等。 出現上述問題后傳統維修方法是將輪轂擴孔，補焊或刷鍍后機加工修復為主，但兩者均存在一定弊端：補焊高溫產生的熱應力無法完全，易造成材質損傷，導致部件出現彎曲或斷裂；而電刷鍍受涂層厚度限制，容易剝落，且以上兩種方法都是用金屬修復金屬，無法改變“硬對硬”的配合關系，在各力綜合作用下，仍會造成再次磨損。 上述維修方法在西方國家已不常見，當代歐美等發達國家針對以上問題多使用高分子復合材料的修復方法，應用最成熟的是美國福世藍技術，其具有的粘著力，優異的抗壓強度等綜合性能，可免拆卸、免機加工進行現場修復。用高分子材料維修既無補焊熱應力影響，修復厚度也不受限制，同時產品所具有的金屬材料不具備的退讓性，可吸收設備的沖擊震動，避免再次磨損的可能，并大大延長設備部件的使用壽命，為企業節省大量的停機時間，創造巨大的經濟價值。 故障排除 常見到經檢修和初次安裝的錘片式粉碎機在試運轉中機身發生強烈振動。出現這種情況主要有以下幾個原因： （1）檢修裝配中錘片安裝錯誤。錘片換面掉頭使用時，為防止轉子重量失去平衡，粉碎機內所有的錘片必須一齊換面掉頭，否則會在運行中發生強烈振動。 （2）對應兩組錘片重量之差超過5克。排除的方法是調整錘片重量，使相應兩組重量之差少于5克。 （3）個別錘片卡得太緊，運行中沒有甩開?？赏C(jī)后用手轉動觀察，想辦法使錘片轉動靈活。 （4）轉子上其他零件重量不平衡，這時需要分別仔細檢查調整平衡。 （5）主軸彎曲變形。解決的辦法是校直或更換。 （6）軸承間隙超過極限或損壞。一般都采用更換新軸承才能解決問題。 Jaw crusher, jaw crusher, jaw crusher, jaw crusher, jaw crusher - jaw crusher, jaw crusher Common faults Fault ioduction Jaw crushers often experience high torque or vibration during operation, which can lead to transmission system failures. Common causes include wear on the shaft head and hub due to clearance between the belt pulley and the shaft head, and wear on the bearing ition due to ecceic shaft stress. After the above problems occur, the traditional maintenance method is mainly to enlarge the wheel hub, repair it by welding or brushing, and then machine repair it. However, both methods he certain drawbacks: the thermal stress generated by high temperature welding cannot be completely eliminated, which can easily cause material damage and lead to component bending or fracture; However, electric brush plating is limited by the thickness of the coating and is prone to peeling off. Both methods use metal to repair the metal and cannot change the "hard to hard" fit relationship. Under the combined action of various forces, it will still cause further wear. The above repair methods are no longer common in Western couies. Developed couies such as Europe and America often use polymer coite materials for the repair of the above problems. The most mature application is the Fushilan technology from the United States, which has super strong adhesion, excellent compressive strength and other comprehensive properties, and can be repaired on-site without disassembly or machining. The use of polymer materials for repair is not affected by welding thermal stress, and the repair thickness is not limited. At the same time, the metal material of the product does not he the flexibility to absorb the impact and vibration of the equipment, oiding the sibility of further wear and greatly extending the service life of equipment components, sing a lot of downtime for enterprises and creating huge economic value. Troubleshooting It is common for hammer crushers that he undergone maintenance and initial installation to experience strong vibrations during trial operation. There are several main reasons for this situation: (1) Installation error of hammer plate during maintenance and assembly. When using the hammer blade with a face change and a U-turn, in order to prevent the weight of the rotor from losing balance, all the hammer blades in the crusher must be face changed and U-turn together, otherwise strong vibrations will occur during operation. (2) The difference in weight between the two sets of hammer blades exceeds 5 grams. The elimination method is to adjust the weight of the hammer pieces so that the difference between the corresponding two sets of weights is less than 5 grams. (3) Some hammer blades are stuck too tightly and do not shake off during operation. After stopping the machine, rotate it by hand to observe and find a way to make the hammer rotate flexibly. (4) The weight of other parts on the rotor is unbalanced, and it is necessary to carefully check and adjust the balance separately. (5) The spindle is bent and deformed. The solution is to straighten or replace. (6) The bearing clearance exceeds the limit or is damaged. Usually, the problem can only be solved by replacing the bearings with new ones.